Influence of small amount of sintering additives on unlubricated sliding wear properties of SiC ceramics
DC Field | Value | Language |
---|---|---|
dc.contributor.author | Kumar, B. V. Manoj | - |
dc.contributor.author | Kim, Young-Wook | - |
dc.contributor.author | Lim, Dae-Soon | - |
dc.contributor.author | Seo, Won-Seon | - |
dc.date.accessioned | 2021-09-07T05:26:33Z | - |
dc.date.available | 2021-09-07T05:26:33Z | - |
dc.date.created | 2021-06-19 | - |
dc.date.issued | 2011-12 | - |
dc.identifier.issn | 0272-8842 | - |
dc.identifier.uri | https://scholar.korea.ac.kr/handle/2021.sw.korea/110972 | - |
dc.description.abstract | Fully densified SiC ceramics were developed from commercially available beta-SiC powders using small amount (3 wt%) of AlN-Sc2O3 or AlN-Y2O3 additives by hot pressing at 2050 degrees C for 6 h in nitrogen atmosphere, and their wear properties were investigated by subjecting to self-mated sliding at different loads (1, 6 and 13 N) under unlubricated conditions. SiC ceramics prepared with 3 wt% AlN-Y2O3 additives consisted of mostly large equi-axed grains with amorphous grain boundary phase of similar to 1.2 nm thickness, whereas SiC ceramics sintered with 3 wt% AlN-Sc2O3 additives showed duplex microstructure of elongated and fine equi-axed grains with clean grain boundary. As the load was increased, the steady state coefficient of friction reduced from similar to 0.6 to similar to 0.2, and wear rate increased from 10(-6) to 10(-5) mm(3)/N.m. It was observed that the friction did not depend on the additive composition, while less wear was observed for the SiC ceramics sintered with 3 wt% AlN-Sc2O3 additives consisting of clean grain boundary. The material loss was increased with the increased amount of sintering additive to 10 wt%. The worn surface morphology revealed that the material was primarily removed via surface grooving and microcracking at 1 N load, while tribochemical wear dominated at 6 and 13 N loads. (C) 2011 Elsevier Ltd and Techna Group S.r.l. All rights reserved. | - |
dc.language | English | - |
dc.language.iso | en | - |
dc.publisher | ELSEVIER SCI LTD | - |
dc.subject | SILICON-CARBIDE CERAMICS | - |
dc.subject | HIGH-TEMPERATURE STRENGTH | - |
dc.subject | GRAIN-BOUNDARY STRUCTURE | - |
dc.subject | MECHANICAL-PROPERTIES | - |
dc.subject | FRACTURE-TOUGHNESS | - |
dc.subject | INTERGRANULAR PHASE | - |
dc.subject | ALUMINUM NITRIDE | - |
dc.subject | RE2O3 RE | - |
dc.subject | BEHAVIOR | - |
dc.subject | MICROSTRUCTURE | - |
dc.title | Influence of small amount of sintering additives on unlubricated sliding wear properties of SiC ceramics | - |
dc.type | Article | - |
dc.contributor.affiliatedAuthor | Lim, Dae-Soon | - |
dc.identifier.doi | 10.1016/j.ceramint.2011.06.018 | - |
dc.identifier.scopusid | 2-s2.0-80053966648 | - |
dc.identifier.wosid | 000296397400083 | - |
dc.identifier.bibliographicCitation | CERAMICS INTERNATIONAL, v.37, no.8, pp.3599 - 3608 | - |
dc.relation.isPartOf | CERAMICS INTERNATIONAL | - |
dc.citation.title | CERAMICS INTERNATIONAL | - |
dc.citation.volume | 37 | - |
dc.citation.number | 8 | - |
dc.citation.startPage | 3599 | - |
dc.citation.endPage | 3608 | - |
dc.type.rims | ART | - |
dc.type.docType | Article | - |
dc.description.journalClass | 1 | - |
dc.description.journalRegisteredClass | scie | - |
dc.description.journalRegisteredClass | scopus | - |
dc.relation.journalResearchArea | Materials Science | - |
dc.relation.journalWebOfScienceCategory | Materials Science, Ceramics | - |
dc.subject.keywordPlus | SILICON-CARBIDE CERAMICS | - |
dc.subject.keywordPlus | HIGH-TEMPERATURE STRENGTH | - |
dc.subject.keywordPlus | GRAIN-BOUNDARY STRUCTURE | - |
dc.subject.keywordPlus | MECHANICAL-PROPERTIES | - |
dc.subject.keywordPlus | FRACTURE-TOUGHNESS | - |
dc.subject.keywordPlus | INTERGRANULAR PHASE | - |
dc.subject.keywordPlus | ALUMINUM NITRIDE | - |
dc.subject.keywordPlus | RE2O3 RE | - |
dc.subject.keywordPlus | BEHAVIOR | - |
dc.subject.keywordPlus | MICROSTRUCTURE | - |
dc.subject.keywordAuthor | Silicon carbide | - |
dc.subject.keywordAuthor | Sintering additives | - |
dc.subject.keywordAuthor | Sliding wear | - |
Items in ScholarWorks are protected by copyright, with all rights reserved, unless otherwise indicated.
(02841) 서울특별시 성북구 안암로 14502-3290-1114
COPYRIGHT © 2021 Korea University. All Rights Reserved.
Certain data included herein are derived from the © Web of Science of Clarivate Analytics. All rights reserved.
You may not copy or re-distribute this material in whole or in part without the prior written consent of Clarivate Analytics.